PRO-2066 150-Channel Mobile Trunking Scanner (200-0195) Features Faxback Doc. # 49848 INTRODUCTION Your new RadioS
A LOOK AT THE KEYPAD Your scanner's keys might seem confusing at first, but this information should help you understand each key's functio
MANUAL - stops scanning and lets you directly enter a channel number or frequency.
TRUNK - appears when the scanner is set for trunk tracking. MON - appears during search modes or when you select a monitor memo
To make it easier to identify and select the channels you want to listen to, channels are divided into 5 banks of 30 channels each. Use each channel
2. Use the number keys and (.) to enter the frequency (including the decimal point) you want to store. 3. Press E to store the frequency into t
HOLD to stop searching so you can listen to the transmission. HOLD appears. MON to store the displayed frequency into the current monit
flash on the display. To select a service bank, press the desired service bank key (WX, CB, HW, PS, HAM, MRN, AIR, POL, or DOT). The corresponding s
memory you want to listen to. Note: To listen to the monitor memories, the priority channel feature must be turned off (see "Priority&qu
step through the channels.) To resume automatic scanning, press SCAN. (BR/eb 9/22/98) PRO-2066 150-Channel Mobile Trunking Scanner (200-0195)
channel, manually select the channel, then press L/OUT. L/O appears. Note: You can still manually select locked out channels. To remove the lockou
systems you can listen to. Triple-Conversion Circuitry - virtually eliminates any
direct search, press H/S. HYPER appears during Hypersearch. Note: You can use Hypersearch only in the 5 kHz step bands (26.965-27.405 MHz, 2
Your trunk tracking scanner can monitor two basic types of systems - Type I and Type II. Instead of selecting a specific frequency to transmit on, a
channel, and, in some instances, can prevent your scanner from acquiring the data channel at all. You must adjust SQUELCH before your scanner can tra
searches for the data channel. While the scanner looks through the frequencies, you see them on the display. When the scanner finds the
scanner stores the ID into the monitor ID memory. 2. Press SEARCH to resume searching. Note: To program the ID stored in the monitor ID memory
delay set, you might need to change the default system type or the fleet map you are using. See "Scanning Type I and Hybrid Trunke
1. Select the trunking bank you want (see "Scanning a trunked Bank" above). 2. After the scanner begins trunk tracking, press MANUAL.
To remove a scan list from active scanning, use the number keys to enter the scan list's number. The scan list number turns off, and the IDs in
S-6 32 8 32 1 S-7 32 4 64 1 S-8 16 4 128 1 S-9 8
2 S11 2 S4 3 S11 3 S4 4 S11 4 S4 5 S11 5 S4
Manual Channel Access - You can directly access any channel to quickly tune a
0 S10 0 S1 1 S10 1 S1 2 S11 2 S2 3 S4 3 S2
E1P13 E1P14 Block Size Code Block Size Code 0 S3 0 S4 1 S3 1 S3
as E1P7). The preprogrammed fleet map appears. 7. Press E, then SEARCH. The scanner then searches for transmissions using the preset map y
designated as Type II blocks. To program a hybrid system, follow the steps listed in "Programming a Fleet Map" above. However, if you want
Poor or no reception. An antenna is not Make sure an antenna is connected or connected connected to the
# 49852. The frequency used Press SEARCH to search
Note: Do not turn off the scanner until CLEAr stops flashing. Otherwise, the scanner might not clear its memory properly. (BR/eb 9/22/98) P
PRO-2066 150-Channel Mobile Trunking Scanner (200-0195) Specifications Faxback Doc. # 49855 Frequency Coverage: ...
Delay Time: ... 2 Seconds IF Frequencies: ... 380.7 MHz, 10.85 MHz, and 450 kH
144-148 5 2-Meter Ham Band 148-174 5 VHF Hi
According to the Electronic Communications Privacy Act (ECPA), you are subject to fines and possible imprisonment for intentionally listening to, usi
other areas that produce extreme heat. WARNING: Use extreme caution when you install or remove an outdoor antenna. If the ante
2. In the marked positions, drill holes slightly smaller than the supplied screws. CAUTION: Be careful not to drill into objects behind th
specifications. Using a power cable that does not meet these specifications could damage the scanner or the power cable. USING T
scanner's internal speaker. Listening Safely To protect your hearing, follow these guidelines when you use an earphone or headphones.
Komentarze do niniejszej Instrukcji